Posted on

SPOG 2CV Parts 2CVGB News article – August 2018

SPOG 2CV Parts

It must be fifteen years or more since I started to help the SPOGman of that time, Pete Abbott, with the distribution of SPOG Parts. There was no 2cvGB Unit at Ruskington back then, all the items being stored here under a bed in the spare room. At that time we currently supplied the 2cv front door A post gutter repair and the Dyane lower windscreen panel besides various other pieces of folded metal. In 2004 I took over from Pete on the 2cvGB Committee but more of that later. Continue reading SPOG 2CV Parts 2CVGB News article – August 2018

Posted on

SPOG 2CV Parts 2CVGB News article – June 2018

SPOG 2CV Parts - two tools Taffy

As some of you are aware my current private email is closing down its email services in the next few weeks. No, this is not a scam, fake news etc but for real. Indeed after having had this email address since I started working with computers, sadly much now has to change. So everybody from the 1st of June, kindly delete my current private contact details and replace with please.

2018 Drive it Day from York ended with me happily parking up at the Airfield in Sherburn in Elmet alongside an E Type Jaguar convertible and a 1992 Ferrari, the owner having bought the number plate before he actually found the car, most illustrious company where the 2CV fits in perfectly. However my 2CV was not beautiful by any means since it was alarmingly spewing oil everywhere. In fact on the run (a mere 80 miles) it used up nearly a litre of engine oil.

Yes this car had been gently losing oil for some months although not on this grand scale, oh dear, something drastically wrong that needed urgent attention. Therefore after coming home, the front wings were removed to find abundant old oil residue scattered throughout the engine bay. Not nice. Where to begin? I detached the lower fibre cylinder head shroud on the near-side (left) expecting to see the oil pressure switch or push rod seals leaking. However when I started the car, no problem here, the oil seemed to be coming from behind the fan somewhere.

Off with the grille, fan and the point box rubber cover. Ah here it is, oil pouring out from the off-side (right) oil cooler union where it fits into the crankcase. Probably the pipe seal has perished/split I thought. Now it’s very difficult to get at these unions with the fan housing in situ. Therefore after having slackened off the gearbox engine mount, I unscrewed the front engine mount bolts and jacked up the engine thereby managing to remove the fan cowling from out under the light bar.  As an aside, one of the front engine mounts had completely disintegrated, something to replace with new when putting everything back together again.

I removed the oil cooler, disappeared into the loft for a pair of new pipe seals and refitted everything accordingly. No different.  Off with the oil cooler again (I do have a 16 mm pipe spanner which does make this task much easier) and looked at the pipe ending on the offending side. A distinct ridge had developed over time on the pipe where it enters and vibrates within the crankcase. The seal cannot seat properly because of this ridge, that’s the problem I thought. So delicately with fine sand-paper, I removed this blemish along with any other surface imperfections.  Oil cooler returned to find the copious leak was still present. I’m getting cross now!

I have “used” oil coolers in the loft but they are of an unknown quality and time was pressing since this car was needed for the TROY Camp in a few days time. A quick journey to Bradford, with 2CV City being open on a Saturday morning (thanks Ash) to buy a new Valeo oil cooler and seals. With the replacement oil cooler fitted the leak had vanished … yippee … I’m happy now. Therefore I must presume that there has to be a crack at the swage against which the pipe union nut presses, this defect opening up when the nut is tightened … something to check for at a later date.

Whilst fiddling around at the front of the engine I couldn’t help but notice that the Cylinder Head’s oil feed pipes on both sides were rather scabby, indeed I’ve been told that the oil pressure within this pipe is over 90 psi. Having already seen what such a force can do to an oil cooler union … as they say … “never spoil a ship for a ha’porth of tar”. I’ve carried a new Citroen Cylinder Head oil feed pipe within my spares for our European travels for many years knowing that if this pipe were to snap or leak (and they do because of age/corrosion etc.) a replacement will be needed  immediately, particularly if the pipe sheers off at the banjo union. Why wait for an overseas disaster to strike? Change the pipe now when everything is suitably exposed.

For access to the right cylinder head oil feed pipe union the lower fibre engine shroud has also to be taken off on this side. Following its detachment, the oil feed pipe was removed and found to be in dire state with distinct craters like the surface of the moon. This job really did need doing. I’ve also learnt over the years from fellow 2CVGB Members that when fitting any oil feed pipe, it is very easy to get the union banjo bolts cross-threaded thereby causing the need for special thread inserts etc. Not a good idea! So every care was taken with this procedure also ensuring that the banjo bolts were returned as per removal, their different drain holes being specific for location.

Alas my Citroen oil feed pipe was made of steel and very reluctant to bend as its shape was nothing like what it should have been. However nowadays there are new copper nickel alternatives (one soon to be bought as replacement for my loft stores) which should prove more pliable and easier to fit. Whatever, after a lengthy struggle with the steel pipe, I managed to get the banjo bolts in position along with new copper washers for hand tightening before the application of my “baby” torque wrench set to 8 ft lbs. As you can see in the relevant photograph, everything looks much better than it did. And to finish, all the shrouds etc were returned to include two new front engine mounts. Job done with the under-car oil drip tray now put away for another day.

But the above is nothing in comparison with the Dyane restoration work currently underway in Holland. Marcel has kindly sent me some wonderful pictures from across the North Sea of his treasure being restored using SPOG’s Dyane rear inner wing panels. Indeed this is what SPOG is all about … having parts manufactured to keep our cars on the road. And with more cars in use rather than being broken or crushed to oblivion, such restored vehicles will inevitably require all the usual servicing spares etc. Hence there is a big enough market for standard trade sources to keep on producing such items. SPOG helps us all.

And finally there will be a SPOG presence at Registers weekend with all the usual “little” bits for sale in the display cabinets. If you want any of the larger panels, Dyane front door window sliding channels etc. then please kindly get in touch beforehand and I’ll bring these along for you. There is only so much stuff you can get into a 2CV.

David Eden


2CVGB Parts (SPOG) supplying specialised, rare or obsolete 2CV parts



Posted on

SPOG 2CV Parts 2CVGB News article – April 2018

2CVGB PArts aka SPOG 2CV Parts

Welcome to the SPOG 2CV Parts article April 2018

Congratulations Scotland for beating France at Murrayfield in the Six Nations Rugby Tournament on February 11th. It was great fun driving my Dolly to be part of the 2CV Ecosse procession through Edinburgh’s streets welcoming the French Supporters to town. And what a cheer these rugger fans gave us as we waved and hooted our arrival. Many thanks to James Storrar and our Scottish 2CV members who organised this wonderful experience, see you again in two years time. Continue reading SPOG 2CV Parts 2CVGB News article – April 2018

Posted on

2CVGB News article – SPOG February 2018

I’ve always been told “you are what you read”. Indeed having no mechanical background before I started restoring and maintaining 2cvs, most of my knowledge has come from studying Workshop Manuals.  Amongst others, the Haynes publication was my constant reference point at the beginning. But what if things are written down incorrectly? Continue reading 2CVGB News article – SPOG February 2018

Posted on

2CVGB News article – SPOG January 2018

Happy Birthday 2cvGB with us becoming forty years old in 2018 although the actual date for celebration is 25th February. On that day back in 1978 our Club held its first meeting in Leamington Spa where committee members were appointed and membership subscriptions began. The first 2cvGB News appeared in April 1978 although I didn’t personally join the Club until 1986 despite having owned a 2cv from new since 1976. That particular car rapidly fell to bits on me and so I passed it on.  However I missed this car so much I quickly bought another one likewise joining the Club to ensure that such neglect and stupidity would never happen again. It hasn’t. Continue reading 2CVGB News article – SPOG January 2018

Posted on

2CVGB News article – SPOG December 2017

With Taffy still beating the drum of rear brakes I’ve more to say about Kieran’s difficulty with bleeding the brake system after fitting new rear LHM wheel cylinders to his ongoing 2CV restoration project. You’ll remember I suggested that either the dust cap cover or “O” ring seal might be the problem causing the piston to retreat into the actual wheel cylinder after pressure is removed from the brake pedal. Continue reading 2CVGB News article – SPOG December 2017